CSWIP 3.1 QUESTION AND ANSWER SERIES
[BUY] CSWIP 3.1 Learning Package
(145mb) Books & Chapter wise Questions (General Paper + Technical Paper) and Answers. Examination notes on Practical Examination of Plate/Pipe CSWIP 3.1 Learning Presentation
$72.00
CSWIP 3.1: Question with Answer and Explanation – Part 1
CSWIP 3.1: Question with Answer and Explanation – Part 2
CSWIP 3.1: Question with Answer and Explanation – Part 3
CSWIP 3.1: Question with Answer and Explanation – Part 4
CSWIP 3.1: Question with Answer and Explanation – Part 5
CSWIP 3.1: Question with Answer and Explanation – Part 6
CSWIP 3.1: Question with Answer and Explanation – Part 7
CSWIP 3.1: Question with Answer and Explanation – Part 8
CSWIP 3.1: Question with Answer and Explanation – Part 9
CSWIP 3.1: Question with Answer and Explanation – Part 10
CSWIP 3.1: Question with Answer and Explanation – Part 11
CSWIP 3.1: Question with Answer and Explanation – Part 12
CSWIP 3.1: Question with Answer and Explanation – Part 13
CSWIP 3.1: Question with Answer and Explanation – Part 14
CSWIP 3.1: Question with Answer and Explanation – Part 15
CSWIP 3.1: Question with Answer and Explanation – Part 16
CSWIP 3.1: Question with Answer and Explanation – Part 17
CSWIP 3.1: Question with Answer and Explanation – Part 18
CSWIP 3.1: Question with Answer and Explanation – Part 19
CSWIP 3.1: Question with Answer and Explanation – Part 20
1) To assess the surface of a weld for direct inspection, the distance from the surface to the eye should be a maximum of?
| a. | 200mm |
| b. ( answer ) | 600mm |
| c. | 60mm |
| d. | 6000mm |
2) What is the recommended minimum range of illumination required by BS EN 970 for inspection of a welded surface?
| a. | 90-125 lux |
| b. | 150-250 lux |
| c. ( answer ) | 350-500 lux |
| d. | 35-50 lux |
3) Who should have access to the WPS?
| a. | NDT operators |
| b. | Inspectors only |
| c. | Welder only |
| d. ( answer ) | Welder and Inspectors |
4) Who has the responsibility of ensuring the welder is using the correct consumable during fabrication?
| a. | The QA department |
| b. | Store man and the welder |
| c. | Welding engineer |
| d. ( answer ) | The welder and the welding inspector |
5) Who has the responsibility of ensuring the welder is using the correct polarity during welding?
| a. ( answer ) | The welder and the welding inspector |
| b. | Store man and the welder |
| c. | Welding engineer |
| d. | The QA department |
6) You notice the welders are adjusting the current on the welding set, is this allowable?
| a. | Never |
| b. | The welder has the final say on voltage and current |
| c. ( answer ) | Only if the current is within the range recorded on the WPS |
| d. | As long as the welder has approval from the welding foreman |
7) Who determines what the correct weld preparation (root gap, root face, included angle) should be?
| a. ( answer ) | The welding engineer |
| b. | The welding supervisor |
| c. | The welder will decide |
| d. | The inspector will recommend what is suitable |
8) What course of action should be taken upon finding a welder using incorrect welding consumable?
| a. ( answer ) | Report the incident and record all relevant information |
| b. | Allow welding to proceed if the workmanship is good |
| c. | None if the tensile strength of the consumable is the same as the approved one |
| d. | Change the electrode for the correct type and continue welding |
9) Who should have access to the WPQRs?
| a. | NDT operators |
| b. | Inspectors only |
| c. | Welders only |
| d. ( answer ) | Welding engineer |
10) Who has the final responsibility of sentencing and accepting a weld on completion?
| a. | The contractor’s inspector |
| b. | Site manager |
| c. | The welder |
| d. ( answer ) | The client’s inspector or certifying authority |
Pls see next part:
AMARINE 
One thought on “CSWIP 3.1: Question with Answer and Explanation – Part 11”